Stamping is also divided into forging, ginning, combining and other types. Processing of iron can be referred to as punching. Conventional press working method is cut, bent, twist. Also there are a variety of molds, including plastic, rubber molds, glass molds. Stamping dies are used for stamping, including arbitration die, progressive die, compound die, precision die, drawing die, bending die, molding, die cutting and other types of stamping dies, according to the differences of the finished product, users can choose different stamping dies.

At the beginning of it, tungsten plate should be blended into a certain angle, or bending the blended workpiece again. After that, it should be pressed into any hollow shape by mould, or bending the hollow mould workpiece further deformation. Afterward the hole or the outer edge of tungsten plate should be folded into a straight wall by mould. Forcing an outward radial force on the hollow member by mould, so that the local diameter can be expanded. After expansion, pressing the outside-in radial pressure on the hollow member so to narrow the local diameter. Next, putting the bloom into the die cavity, squeeze it out from the gap of mould to form the hollow or solid workpiece. Roll the panel into a ball peen whose shape approximate to a close one. Finally, press the bended or stretched workpiece into a right stamping tungsten boat shape.

The main features of the stamping W-boat is the high rate of final products. Because that this type of W-boat adopting the stamping equipment and stamping mould, the accuracy of size and shape the stamping wolfram crucible are much higher. What’s more, it has a long life time and it is not easily to be damaged, therefore, the shape of the stamping tungsten boat from the same production batch is almost the same whose quality is also stable. However, during the stamping process, the device will produce noise and vibration which would have a great influence on operators. Furthermore, the mould is an essential material for stamping process, so the quality of the mould determines the quality of the W-boat.

Surface and internal performance of panel have a great impact on the quality of the finished product by stamping, it requires that the thickness of stamping material should be precise and without any spots, scars, bruises, surface cracks.

Jena Analytik Jena AG brand, called AJ, was established in 1990 in Germany, which is evolved by Carl Zeiss Carl -Zeiss Jena GmbH. Nowadays, AJ carbon sulfur analyzer has become one of the most popular brands of analytical instruments in Germany. The brand is mainly focus on the development, design and manufacturing of total organic carbon (TOC) / total nitrogen (TN) analyzers, organic halogen compounds (AOX) analyzer elements (C, S, N, Cl) analyzer, atomic absorption spectrometer (AAS), ICP-OES emission spectrometers, inductively coupled plasma mass spectrometry and UV / visible (UV / VIS) light meter points and biochemical analytical instruments. Analytik Jena is a provider of analytical measuring technology, and life science instruments. With its core expertise in optical spectroscopy and elemental analysis its portfolio includes analytical systems for qualitative and quantitative analysis of liquids, solids, and gases. 

Multi EA S® 5000 Elemental Analyzer is launched by AJ brand in 2008, which is a kind of multi-element professional analysis system for the analysis of total nitrogen, total carbon, total sulfur, total chlorine content of a variety of gaseous, liquid, LPG, solid samples. The instrument has many excellent features. Tungsten granule is used as the mainly flux, which can the accelerate reaction rate for the analysis process, shortening the time of determination. Its appearance and structure design is the main attraction, users can select the elements to be analyzed and the corresponding detector.

In the software you can choose to switch carbon and sulfur analysis, without any mechanical conversion. In addition, AJ carbon sulfur analyzer is a lightweight instrument, which does not require any maintenance vertical injector and a vertical furnace, so that it can ensure that good reproducibility of the instrument. After installation is completed, it doesn’t need any manual adjustment. Voltage stabilizing system in the gas circuit is equipped to avoid the pressure fluctuations while detecting. Any parameters of instrument are set and optimized and controlled by computer, which has the characteristics of full intelligence and full automation. Because the instrument has a heated filter device, there is no need for membrane dryers and detection system to be maintained repeatedly, which can greatly reduce operating costs.

Nuclear electricity generation is the use of fissile materials in nuclear reactors (such as uranium-235, plutonium-239, uranium-233, etc.) that release thermal energy by nuclear fission to generate electricity. Nuclear fission is a radioactive decay process in which the nucleus of an atom splits into smaller parts. The fission process often produces free neutrons and gamma photons, and releases a very large amount of energy. A nuclear chain reaction occurs when one single nuclear reaction causes an average of one or more subsequent nuclear reactions, thus leading to the possibility of a self-propagating series of these reactions. Nuclear chain reaction is the precondition of nuclear electricity generation. Compared with thermal power generation, which uses thermal energy generated by the combustion of chemical fuels to generate electricity, the heat energy released from the nuclear reactor is much higher than that released from the combustion of fossil fuels, while the volume of fuels required is much less.

Fission fragment which is generated when the nuclear fission of nuclear fuels is radionuclide that will occur a series of decay with strong radioactivity (mainly are β-ray and γ-ray). β ray is a high-energy, high-speed electron or positron, whose penetrating power is stronger than α-ray. When it penetrates the skin, it can cause radiation injury. And when it enters the body, it will change the chemical balance of cells, causing cells to become cancerous and the genetic material DNA to be damaged; the penetrating power of γ-ray is also very strong, it can enter into human body to interact with cells in vivo, to damage the molecular components of living cells (such as proteins, nucleic acids and enzymes), leading the body's normal chemical processes to get disturbed, thus causing harm to humans. Neutron radiation emitted by nuclear reactor also has manifested the very strong lethality, it can cause organ failure, central nervous system and digestive system damage.

Tungsten alloy shielding can be used for shielding the radiation released from the process of nuclear electricity generation. Experts find that radiation exposure could be reduced by maxing shielding. The radiation shielding ability of a material is related to its density. Higher density means better radiation shielding ability. Due to a higher density, tungsten heavy alloy has a much higher radiation shielding ability than lead. Alternatively equal amounts of tungsten alloy shielding provide diminished exposure risks than equivalent lead shielding. 

The Metal Injection Molding (MIM) of insoluble metal is mainly used for manufacturing parts with complex and small size. The metal which produced by MIM isn’t has particularly high temperature strength and fatigue performance, but it can save a high of insoluble metal machining costs to achieve a nearly net shape. Traditional tungsten electrodes were produced by sintered tungsten bar and after machining to obtain pure or rare earth tungsten electrodes. Tungsten has highest melting point in insoluble metal, so machining is difficult and the cost is high, so using MIM to produce tungsten electrodes used in lighting equipment are more and more attention and favor in manufacturers. Compared with traditional method, tungsten electrode manufactured by MIM not only has complex shape which can use in different lighting equipment, but also has good performance. Pure tungsten and doped tungsten (AKS-W) is a common anode material, and thoriated tungsten, barium tungsten, and lanthanated tungsten electrode is often used as a cathode material.

Lanthanum tungsten electrodes (W-La₂O₃) manufactures by MIM, and the production processes are as following:
1. The La (NO₃) ₃ • 6H₂O was dissolved in alcohol and then mixed with tungsten powder (0.1um), in which La₂O₃ addition is 1.5%.
2. Place the mixture into a mixing ball mill for 24h, and then to employ drying and screening process. The milling medium is alcohol, grinding body is tungsten rod.
3. The sieved powder is baking and reduction at 600 ℃, so that La (NO₃) ₃ will decompose into La₂O₃.
4. Using paraffin-polymer binder to produce MIM feed. Determine the critical powder load in feed by torque rheometer. Since 1um tungsten powder produced feed has good flow, so the loading is used 55% of the volume fraction. Besides, the compounding temperature is 158 ℃, and roller speed is 60r / min.
5. Then after injection, degreasing and sintered will obtain lanthanated tungsten electrode.