A novel Cs_xWO₃/ZnO smart coating was proposed to achieve multiple functions, such as heat insulation, photodecomposition of toxic NO gas, blocking of harmful UV light, etc. In this composite coating, Cs_xWO₃ nanorods were used as a NIR and UV light shielding material while ZnO nanoparticles were utilized as a photocatalyst and a material to enhance visible light transmittance and block UV light. When the mass ratio of Cs_xWO₃/ZnO was 1, the composite coating possessed a very good visible light transmittance of over 80% and an excellent UV-shielding ability. This novel coating showed heat insulation that is superior to the ITO coating and photocatalytic decontamination of NO gas that is superior to the standard TiO₂ (P₂₅). The proposed Cs_xWO₃/ZnO smart coating is a promising material not only for energy saving but also for environmental cleanup.

The various nanoparticles have been investigating the continuous and new methods to reduce solar heat as it ensures a potentially low-cost and high-productivity solution. Not only does it needs high transmittance of ultraviolet radiation but also achieves complete shielding of infrared solar radiation can be used for solar control windows. In the other word, an effective IR absorbent should have high absorbance as well as a broad working wavelength. A well known the kinds of materials to realize the purpose is the nanoparticles of transparent oxide conductors with heat-ray cut-off effect such as tin doped indium oxide (ITO) and antimony doped tin oxide (ATO). They also are well known to provide highly transparent solar filters to absorb heat-ray by the effect of the plasma vibration of the free electrons, as typically observed in gold and silver nanoparticle solution. However, ITO can only shield the IR wavelength ranges longer than 1500 nm as well as indium is an expensive metal resource. In recent years, for practical application, tungsten bronzes actively have been investigating due to their interesting electro-optics, photochromic, electrochromic, and superconducting properties. Tungsten trioxide (WO3) has a wide band gap of 2.6-2.8 eV5 and is transparent in the visible and NIR ranges. A metallic conductivity and a strong NIR wavelength absorption can be induced when free electrons are introduced into crystals by either decreasing the oxygen content or by adding ternary elements. The oxygen deficiency in tungsten oxides leads to a complex-ordered structure known as the Magneli structure, while the ternary addition of the positive ions leads to the tungsten bronze structure. In other words, tungsten bronzes MxWO3 with doping small ions such as H+, Ag+, Li+, Na+, K+ and Cs+ into WO3 have better optical and electrical properties. It has been reported that the tungsten bronzes with the hexagonal phase are of particular interest in the application of electrochromic devices owing to the relatively high diffusion coefficients of hydrogen ions and metal ions compared with those of the orthorhombic phase and pure WO3.

Generally, due to the cutting force of down milling, the workpiece is pressed against the table so that it is a priority, unless there is a thread gap or other problems considering up milling. Based on this theory, the relevant researchers have proposed the idea of tungsten carbide staggered-edge end mill. Compared with conventional D-edge end mills, tungsten carbide staggered-edge end mill has D-proximal portion, near the handle L-interleaved design, which the original design concept is intended to apply to new carbon fiber composite material. The specific design schematic diagram shown as follow:

From the schematic above we can clearly see that tungsten carbide staggered-edge end mill has two parts, the workpiece processed should be in the middle area between the two cutting edges. Due to the cutting edge is used in the proximal portion of the edge right-handed, left-handed edge near the handle of the staggered design, the lower section of the right-handed cutting edge of the lower surface of the workpiece can be milled, while at the same time under the surface but also by the upward the cutting force; on the contrary, the upper surface of the upper left-hand cutting edge end mill for milling a workpiece and produces its downward cutting force.

In the overall cutting process, the mill closely pressed against the workpiece and feed, so the fiber layer top and bottom surfaces of the material are more likely to be cut off, which effectively avoid the workpiece upper and lower surfaces tears, burrs and other processing defects. In addition, Since the upper and lower surfaces of the workpiece by the cutting force component perpendicular to the contrary, the axial force is reduced and the overall direction of the cutting force is moderate, toward the inside of the workpiece, which is conducive to smoothly throughout the cutting process, but also inhibit stratified of the inner portion of the workpiece. It is possible to improve processing quality carbon fiber composite material to a certain extent. The milling test shows that under the same cutting conditions, grain wear is the main pattern of tungsten carbide staggered-edge end mill. And compared with conventional tungsten carbide end mills, it has better wear resistance and service life.

Tungsten carbide staggered-edge end mill is usually composed of tungsten carbide (WC) + cobalt (Co) and other additives by compacting and sintering. Tungsten carbide mills has broad scope of application, such as CNC machining, engraving and some ordinary milling machining for hard material with simple shape of heat-treated material. According to the shape of edge, it can be specifically divided into integrated tungsten carbide mills, tungsten carbide cylindrical mills, tungsten carbide facing mills, tungsten carbide shank-groove mills, tungsten carbide helical mills, tungsten carbide staggered-edge end mills, tungsten carbide side cutter, tungsten carbide end mills, tungsten carbide saw blade mills, tungsten carbide angled mills and so on.

Generally, tungsten carbide staggered-edge end mill used for stepped surface machining grooves and other parts. The edge located in the circle and surface, which can not be fed in the axial direction only when the legislation is available on the cutter and the axial center of the edge through the end of the feed. This makes the milling edge design focus shifted to how to reduce the axial thrust generated by the tool in the cutting process in case of restraining layer, tear and burrs. Viewed from the direction of feeding and rotating of tungsten carbide mills for the workpiece, it mainly includes two kinds, one is up milling, the other is down milling. The so-called up milling means that the feed direction of the rotational direction of the cutter and cutting the same at the beginning of the milling cutter on the workpiece until the last; while the opposite direction of feed milling cutter rotation and the cutting, before beginning the milling cutter must be some slippage on the workpiece, cutting thickness from scratch when cutting until the end of the maximum thickness.

Another failure form of tungsten carbide wear plate is solder peeling bore wear. Under the impact of concrete, the surface of the ring alloy plate glasses has cracks, which is due to poor wear resistance of its internal bore, can not fully resist the impact of concrete and wear. Flowing concrete will has relative movement with internal bore of tungsten carbide wear plate, which makes the solid surface and the material properties of the surrounding surface has changed, easily deformed due to uneven force. Therefore, enhanced tungsten carbide wear plate bore is critical and it has enhanced the protection of surface alloy ring and reduces the deformation effect. In order to improve the service life of tungsten carbide wear plate, we can improve the wear resistance of internal bore of wear plate from material and structure.

We have two choices from the material that welding electrode wear and use tungsten carbide directly. By experimental comparison can be drawn with the following electrode wear carbide abrasive wear table:

From the graph above we can clearly see that the wear resistance of tungsten carbide is 5 times better than the welding electrode so that tungsten carbide as the material for the internal bore is a best choice. For the bore structure of wear plate, in order to avoid high temperatures generated inlaid alloy caused defects, the researchers used a related set of inlaid alloy structure, effectively extends the life of tungsten carbide wear plate.